Binance APK

List of contents of this article:

• 1,Binance APK How to paste car film
• 2, How to apply film to cars
• 3, correct pasting method of car film
• 4, Methods and steps of car film?

How to stick the car film

1. Clean the car body and keep it dry. Determine the position that needs to be pasted. Under normal circumstances, slowly paste it, scrape it flat with a tool, and remove the bottom paper.If the graphics are too small, you can also tear off all the transparent transfer film and stickers before pasting. But you must be careful not to cause accidental adhesion.

2. The specific steps of car film are as follows: external cleaning Move clockwise along the car (starting from the position of "1 o'clock" and the position of the passenger's front door). The outer surface of each glass should be well cleaned, and the potential dust should be controlled to a minimum extent, and each glass should be slightly lowered to scrub the glass. The top, because there is more dust there.

3. Use a special glass cleaner to remove dirt attached to the glass while removing dust. Covering Cover the dirty parts of the film, such as the car door.

4. Step 4: Stick the film. Tear off the film, spray water evenly on the effective film surface, and put the torn plastic film aside for later use.

5. When pasting the film, it is necessary to avoid sticking it on scratched or raised glass, so as not to affect the fitting effect. Car film is a kind of protective film attached to car glass, which can effectively prevent the damage of ultraviolet rays, thermal radiation and glare to the driver and the items in the car.

6. Car film is a difficult technical work, and the process of filming will also affect the final effect; some car owners have strong hands-on ability and complete tools will choose to apply the film by themselves.

How to apply film to the car

1. The specific steps for applying film to the car are as follows: external cleaning Move clockwise along the car (starting from the position of "1 o'clock" and the position of the passenger's front door), and the outer surface of each glass should be well cleaned. Wash, potentialDust is controlled to a minimum extent, and each piece of glass is slightly lowered to scrub the top of the glass, because there is more dust there.

2. The specific method of car film is as follows: vehicle cleaning: wash the car, clean the inside and outside of the car, and drive the car to a clean and dust-free place to wait for the film to be applied.

3. Clean the car body and keep it dry. Determine the position that needs to be pasted. Under normal circumstances, slowly paste it, scrape it flat with a tool, and remove the bottom paper. If the graphics are too small, you can also tear off all the transparent transfer film and stickers before pasting. But you must be careful not to cause accidental adhesion.

The correct sticker of the car film Method

Tear open the film, spray water evenly on the effective film surface, and put the torn plastic film aside for later use.

The specific steps of car film are as follows: external cleaning, move clockwise along the car (starting from the "1 o'clock" position, the position of the passenger's front side door), the outer surface of each glass should be thoroughly cleaned, the potential dust should be controlled to a minimum extent, and each glass should be slightly lowered to scrub the top of the glass. Department, because there is more dust there.

Step 1: Fill the sprayer with water first. You can add a few drops of detergent or water appropriately. Step 2: Spray water on the first car glass. Step 3: After spraying water, it is to cut the approximate size of the film first.

Methods and steps of car film?

Steps for car film: tailor the car film according to the size of the car window; wipe and clean the front and rear window glass; use a roasting gun to shape the car film; fine-cut the car film after the baking film is completed.

Step 1: Wash the car, clean the inside and outside of the car, and drive the car to a clean and dust-free place and wait for the film to be applied. Step 2: Measure the size of the car window and cut the film according to the size. The size must be appropriate. If you can't grasp it accurately, the size can be slightly larger, but not smaller.Step 3: Clean the window glass.

Test method 1 Test the thermal insulation effect In regular car beauty shops or 4S stores, infrared test lights are generally equipped, so you can ask the merchant for a corner car film to stick to the glass first, put the test light on one side, and put your hand on the other side to feel the thermal insulation effect of the film.

Measure the size of the window and cut the film according to the size. The size must be suitable. If you can't be sure, the size can be slightly larger, but never smaller. Clean the window glass. This step is very important, because if there is dirt on the glass, even a little, it will affect the effect of the film.